In addition to the spout and handle, an outdoor faucet’s other components are crucial to its operation. Although it might be shocking, a typical outside faucet type has nine different pieces.
So, you are here for an outdoor faucet parts diagram?
At a glance, here are the 9 parts that make an outdoor faucet. The parts are Supply pipe, Wall mount, Spigot, Valve seat, Stem washer, Spindle, Packing washer, and Packing Nut. Even though the supply pipe isn’t part of the outside faucet, there is no water without the supply line.
The tip of the iceberg is just the beginning. More to come. Stay tuned and read along.
Outdoor Faucet Parts Diagram
Depending on how old the outdoor faucet is, you will have to repair some of the pieces. Here you will find an old outdoor faucet parts diagram. What you’ll need to look for is shown in the figure below.
1. Handle
The outdoor water faucet parts diagram shows you that the handle is mainly a component. Plastic or silicone can grip an outside faucet without your hands. The most popular shape is a wagon wheel since the handle twists.
The handle might also have wings extending from the middle. Turning the spigot handle left or right, open and close it. Turning it left allows water to flow; turning it right stops it.
2. Packing Nut
At the top of the housing, the packing nut, or bonnet nut, is where the handle will be attached to the faucet. It screws in firmly and is usually made of metal. This item is designed to keep the handle attached to the packing washer for safety reasons. It’s also for preventing leaks.
3. Packing Washer
The packing washer can seem a little unimportant component of an outdoor faucet. It is the element that goes beneath the packing nut. Despite its size and appearance, it serves a very crucial purpose.
The packing washer prevents the faucet from spraying water when turned on. Because packing washers deteriorate. If water leaks or sprays up from this part of the faucet, replace the packing washers. If you find this to be the case, then you should look into replacing the packing washer.
4. Spindle
The stem is another name for the spindle. It is located between its handle and the valves. The spindle mainly aids in controlling the water flow. This long, thin tube flows vertically the entire length of the tap. You can see it in theoutdoor commercial faucet parts diagram very clearly.
For the faucet to perform correctly, the spindle must be in good operating condition. Depending on how the faucet’s handle is rotated, the spindle is pushed downward or upward.
That’s how the spindle helps in opening or closing the valve and allowing or preventing water from exiting the spigot.
5. Supply Pipe
The supply pipe is not technically a component of the faucet itself. However, the supply pipe is an essential component connected to the faucet. When it is installed into the wall, the outdoor faucet will be installed straight against the supply pipe.
And then, the pipe will be lined up so that it feeds straight into the rear of the faucet. It will complete the mounting process. The water from the faucet will have originated from the supply line before reaching its final destination.
6. Stem Washer
The stem washer attaches to the spindle’s stem. It triggers and twisting right forces the stem washer against the valve seat. The stem washer stops water from flowing through, turning off the faucet.
Outdoor faucets include a tiny but essential part that might deteriorate with time. Your faucet’s stem washer probably requires replacing. The tap is broken if water drips from the spigot, even when the faucet is turned off.
7. Valve Seat
The valve seat is positioned and can be found underneath the central body part of the faucet. It controls the flow of water by resting on the bottom of the faucet.
When one wishes to halt the flow of water from the faucet, one presses the stem washer on this portion of the faucet. Water can flow freely from the Spigot when the stem washer is raised and no longer pressed against the valve seat.
If the outdoor faucet leaks from the Spigot, replace the stem washer first. It is true in most circumstances. If a new stem washer does not help, you should check the valve seat since worn valve seats can cause leaks.
8. Spigot
Some people call a faucet’s whole body a spigot,’ although a spigot is merely the end where water runs out. The Spigot may be linked to a hose line or sprinkler system for shallower watering of flower gardens and lawns.
9. Wall Mount
The wall mount is the only way to attach the faucet to the house’s exterior safely. The first step will be to drill a few holes in the house’s façade to secure it. The supply line from the house is then connected to the faucet housing.
FAQ
What Is The Difference Between A Hose Bib And A Spigot?
The term “spigot” refers to an outside faucet in the same way as “hose bib” does. However, the term “spigot” is often used by plumbers and other specialists.
How Does An Outdoor Faucet Stem Work?
Outside spigots and hose bibs feature compression-style valves. When you move the handle counterclockwise, the valve stem presses on the valve seat. Both the valve stem and housing need matching threads to work.
Last Words
We are at the very last of our conversation today. I believe this article comes in handy for you.
You’ll find an outdoor faucet parts diagram in this article. The best thing is that each component is described in great detail. With this diagram, I’m primarily concerned with the pieces of an outside faucet. So that you can do whatever you want to do.
Be Safe and be productive. Good Luck.